WonderMedia Technologies, Inc. W-Load Version : 0.19.00.01 ethaddr............found U-Boot 1.1.4 (Oct 8 2010 - 10:39:28) WonderMedia Technologies, Inc. WMT U-Boot Version : 0.12.01.00.27 U-Boot code: 03F80000 -> 03FC87A4 BSS: -> 04019DAC RAM Configuration: Bank #0: 00000000 128 MB boot from spi flash. flash: Bank1: FF800000 -- FFFFFFFF Bank2: FF000000 -- FF7FFFFF Flash: 16 MB In: serial Out: serial Err: serial bootcmd="run usblogocmd;run nandlogocmd" LCD param (setting): 1,30000,8,800,480,48,40,40,3,29,13,d8110508|10,d8110504|10, d8110500|10 PWM param (setting): 0,25,100,90,98,38,8,0,27 LCD FrameBuffer = 0x07600000, BMP Address = 0x03C00000 Execute register operation for LCD: reg op: 0xD8110508 | 0x10 reg op: 0xD8110504 | 0x10 reg op: 0xD8110500 | 0x10 PWM0 input freq = 47916666 Hz, output freq = 19166 Hz PWM0 register setting: scalar = 24, period = 99, duty = 89 LCD init OK "Loading OS Image ..." usb usb1: Product: USB Host Controller usb usb1: Manufacturer: Linux 2.6.10_dev-VT8610 ehci_hcd usb usb1: SerialNumber: pci-echi 1-0:1.0: USB hub found 1-0:1.0: 2 ports detected locktree(): line: 1024: this function not completed usb 1-: new high speed USB device using abc and address 2 usb 1-: Product: Mass Storage usb 1-: Manufacturer: Generic usb 1-: SerialNumber: 06486D27 scanning bus for storage devices... qtd_copy_status(): line: 176: not imp lement, check again ## Valid DOS partition found ## part_offset : 1, cur_part : 1 1 Storage Device(s) found usb 1-+11111111010000: new high speed USB device using abc and address 3 usb 1-+11111111010000: Product: USB2.0 Hub scanning bus for storage devices... 1 Storage Device(s) found ## Valid DOS partition found ## part_offset : 80002, cur_part : 2 reading logo.bmp Tina_Match: isdir 0x0###################### mydata : Size of clusters in sectors : 1 The sector of the first cluster, can be negative : 81e Current FAT buffer : 03f4c0f0 fatbufnum : ffffffff Length of FAT in sectors : 800 Size of FAT in bits : 20 Starting sector of the FAT : 20 Start sector of root directory : 820 ... 0x5ECF2 bytes read show logo ..... LCD already initialized Loading BMP ..... colorBits = 24 logo_width = 524, logo_height= 247 lcd_width= 800, lcd_height = 480 ok maddr = 0x3c00000, naddr = 0x3e00000 <1> Read header Un-know id = 0x0 Un-know id = 0x0 Err : Can not find any nand flash Init Flash Failed rc=-1 Header is 0xecf24d42 0x00000005 error: magicNum = 0x5, it should be 0x80101000 show logo ..... LCD already initialized Loading BMP ..... colorBits = 24 logo_width = 524, logo_height= 247 lcd_width= 800, lcd_height = 480 ok REG32_VAL(0xd8000440) = 0x08080800 memory size: 128MB ### main_loop entered: bootdelay=1 Execute register operation: reg op: 0xD8110064 | 0xC reg op: 0xD811008C | 0xC reg op: 0xD81100B4 & 0xFFFFFFFB reg op: 0xD81100B4 | 0x8 reg op: 0xD8130054 | 0x1 ### main_loop: bootcmd="run usbbootcmd;run nandbootcmd;go 100000" Hit Enter key to stop autoboot: 1  0 ATSMB Host 390KHz Found SD Card scriptcmd start: ATSMB Host 390KHz Init : SD Card ! Init : card selected ! SD:Four Bits Mode! Initial SD Card OK! ATSMB Host 25MHz SD clock is 25Mhz register mmc device ## Valid DOS partition found ## part_offset : 800, cur_part : 1 --> fatload mmc 0 0 script/scriptcmd ## Valid DOS partition found ## part_offset : 800, cur_part : 1 reading script/scriptcmd Tina_Match: isdir 0x1###################### mydata : Size of clusters in sectors : 8 The sector of the first cluster, can be negative : 148 Current FAT buffer : 03f4d440 fatbufnum : ffffffff Length of FAT in sectors : 98 Size of FAT in bits : 10 Starting sector of the FAT : 8 Start sector of root directory : 138 0xF5 bytes read ## Executing script at 00000000 ** Script length: 173 ** exec: "lcdinit" LCD param (setting): 1,30000,8,800,480,48,40,40,3,29,13,d8110508|10,d8110504|10, d8110500|10 PWM param (setting): 0,25,100,90,98,38,8,0,27 LCD FrameBuffer = 0x07600000, BMP Address = 0x03C00000 Execute register operation for LCD: reg op: 0xD8110508 | 0x10 reg op: 0xD8110504 | 0x10 reg op: 0xD8110500 | 0x10 PWM0 input freq = 47916666 Hz, output freq = 19166 Hz PWM0 register setting: scalar = 24, period = 99, duty = 89 LCD init OK ** exec: "cleanlcd" ** exec: "textout 30 30 "Starting live SD Linux ..." 00ffff" "Starting live SD Linux ..." ** exec: "sleep 1" ** exec: "mmcinit" ATSMB Host 390KHz Init : SD Card ! Init : card selected ! SD:Four Bits Mode! Initial SD Card OK! ATSMB Host 25MHz SD clock is 25Mhz register mmc device ## Valid DOS partition found ## part_offset : 800, cur_part : 1 ** exec: "fatload mmc 0 0 /script/uzImage.bin" ## Valid DOS partition found ## part_offset : 800, cur_part : 1 reading /script/uzImage.bin Tina_Match: isdir 0x1###################### mydata : Size of clusters in sectors : 8 The sector of the first cluster, can be negative : 148 Current FAT buffer : 03f4c0e8 fatbufnum : ffffffff Length of FAT in sectors : 98 Size of FAT in bits : 10 Starting sector of the FAT : 8 Start sector of root directory : 138 0x265F08 bytes read ** exec: "setenv bootargs mem=112M root=/dev/mmcblk0p2" ** exec: "bootm 0" ## Booting image at 00000000 ... Image Name: MontaVista Linux 2.6.10 Image Type: ARM Linux Kernel Image (uncompressed) Data Size: 2514632 Bytes = 2.4 MB Load Address: 00008000 Entry Point: 00008000 Verifying Checksum ... OK OK No initrd ## Transferring control to Linux (at address 00008000) ... Starting kernel ... Uncompressing Linux............................................................. ................................................................................ .................. done, booting the kernel.